MWD which in full is Measurement While Drilling is measurement taken when drilling on an angle of inclination to the vertical line. These measurements are taken by the MWD Drilling Software. This data is used to produce a 3-D plot of the path of the oil well. This software will transmit crucial information to the operator during operations.
The software transmits information on the direction the well is being drilled. Directional survey can be done by the software and sent in real time. Azimuth and the inclination angle of the drill hole are measured by the magnetometers and accelerometers in it. Immediately information on them has been measured it is transmitted to the surface for analysis
The data transmitted at intervals of 10m to 500m is then analyzed on the surface to calculate the location of the wellbore. It is necessary information for the company since it acts as a proof that it is not operating outside the block it is licensed to prospect. When operating vertically or near vertical direction this technology is not used due to its high cost.
The surveys is mainly used in directional-drilling. Directional-drilling forms the main or core part of any survey. Finding and moving towards the target zone of the well will be made easier by this information. Directional-drilling is aided by MWD by the provision of tool face measurements which uses downhole mud motors with bent housing or bent.
Information on the drilling mechanics on the drill bit is also send by the software. Downhole temperature, smoothness of rotation, and operation speed of the rotation are some of the measurements taken. Weight and torque of the bit information aid in operating more efficiently. The driller monitors the tools used from this information to make sure they are working as per the technical specifications. Geologists have a use for this information which is to determine the rock formation of that area.
Drillers use information from the MWD tools for performing geosteering to the zones targeted. The software sends formation properties of the area being drilled at that moment. This kind of information will be on porosity, inclination of the drill bit, the resistivity and the acoustic-caliper which is very important to the driller.
The internal gamma ray sensor using installed in MWD tools measures the natural gamma rays values at the well. The sensors are inexpensive, compact and are able to take the measurements when working on unmodified drill collars. MWD computer programs cuts the process costs and increases the life-span of the drill bits.
There are two types of transmission of data on drilling; either mud-pulse telemetry method or electromagnetic telemetry. The functioning of the mud-pulse telemetry method is where the mud valve deep down the hole restricts the flow of slurry thus brings about the differences in pressure which are sent to the surface for further analysis. There are three types of pulses; positive, negative pulse or continuous wave.
In electromagnetic telemetry method by the MWD software, altered voltage is generated in the upper and lower part of the electrical insulator then incorporated in the drillstring. There is a wire from both thewellhead on the surface and the rod which form the electrodes of a dipole antenna. These electrodes provide information from analysis of the voltage signals.
The software transmits information on the direction the well is being drilled. Directional survey can be done by the software and sent in real time. Azimuth and the inclination angle of the drill hole are measured by the magnetometers and accelerometers in it. Immediately information on them has been measured it is transmitted to the surface for analysis
The data transmitted at intervals of 10m to 500m is then analyzed on the surface to calculate the location of the wellbore. It is necessary information for the company since it acts as a proof that it is not operating outside the block it is licensed to prospect. When operating vertically or near vertical direction this technology is not used due to its high cost.
The surveys is mainly used in directional-drilling. Directional-drilling forms the main or core part of any survey. Finding and moving towards the target zone of the well will be made easier by this information. Directional-drilling is aided by MWD by the provision of tool face measurements which uses downhole mud motors with bent housing or bent.
Information on the drilling mechanics on the drill bit is also send by the software. Downhole temperature, smoothness of rotation, and operation speed of the rotation are some of the measurements taken. Weight and torque of the bit information aid in operating more efficiently. The driller monitors the tools used from this information to make sure they are working as per the technical specifications. Geologists have a use for this information which is to determine the rock formation of that area.
Drillers use information from the MWD tools for performing geosteering to the zones targeted. The software sends formation properties of the area being drilled at that moment. This kind of information will be on porosity, inclination of the drill bit, the resistivity and the acoustic-caliper which is very important to the driller.
The internal gamma ray sensor using installed in MWD tools measures the natural gamma rays values at the well. The sensors are inexpensive, compact and are able to take the measurements when working on unmodified drill collars. MWD computer programs cuts the process costs and increases the life-span of the drill bits.
There are two types of transmission of data on drilling; either mud-pulse telemetry method or electromagnetic telemetry. The functioning of the mud-pulse telemetry method is where the mud valve deep down the hole restricts the flow of slurry thus brings about the differences in pressure which are sent to the surface for further analysis. There are three types of pulses; positive, negative pulse or continuous wave.
In electromagnetic telemetry method by the MWD software, altered voltage is generated in the upper and lower part of the electrical insulator then incorporated in the drillstring. There is a wire from both thewellhead on the surface and the rod which form the electrodes of a dipole antenna. These electrodes provide information from analysis of the voltage signals.
No comments:
Post a Comment